MIBO 1/10 Offroad Low Profile (0.07s/20kg/8.4V) Brushless Servo

Produttore:
MIBO
Categorie:
Codice prodotto:
#MB-2313
Il tuo prezzo:
89,90 €
Disponibilità:
abbastanza disponibile, Invio 3. 4.
Tu ricevi:
Europa4. 4.
MondoStimato 5. 4.

Very high torque/very high speed programmable digital low-profile brushless servo with steel gear and double BB-ed output shaft. Works great in 1:10 off-road RC cars. All-aluminium case for perfect cooling under high load.

MB-2313 is programmable using the KAVAN servo USB programmer/interface and PC software.

Programmable Functions:
  • Servo Angle: Maximal servo rotation angle range setting. The default range is ca 120° within the regular RC signal pulse width range (900~2100 µs); ca 180° within the max. signal pulse width range (500~2500 µs).
  • Servo Neutral: Servo neutral (centre) position setting. 
  • Damping Factor: Servo damping setting – adjust the characteristics of the servo when stopping. 
  • PWM Power: Adjusts the servo output power. The higher the power, the higher the speed and torque of the servo – indeed also the current consumption will be higher. 
  • Sensitivity: Servo sensitivity (Dead Band) setting. The higher sensitivity the narrower the dead band – servo moves only if the change of the signal pulse width is bigger than the dead band width. Too high setting may cause servo jitter in some applications. Range: Ultra High (ca 1 µs dead band) – High (ca 2 µs) – Medium (ca 3 µs) – Low (ca 4 µs) 
  • Soft Start: Turns on/off the soft start feature. If ON, the servo goes slowly to the initial position corresponding to the servo signal once the power is switched on. 
  • Reverse: Reverses the servo movement direction. 
  • Narrow Band: FUTABA SR Mode – only for use with FUTABA radio channels working in the SR mode. Do not turn the option on if you are using a different setting of your FUTABA radio or any other radio. 
  • SANWA SSR: SANWA SSR Mode - only for use with SANWA radio channels working in the SSR mode. Do not turn the option on if you are using a different setting of your SANWA radio or any other radio. 
  • Lost PPM Protection (Fail-Safe): In the case the control signal from the receiver is lost completely or cannot be decoded correctly (due to interference) the servo can use choose one of three fail-safe modes: 
    • (a) Release: No fail-safe protection. 
    • (b) Keep Position: Keeps the position corresponding to the last correct control signal. 
    • (c) Go Neutral Position: The servo returns to the neutral (1500 µs pulse width) position. 
  • Over Load protection: Enables or disables overload protection of the servo in three levels – once the overload conditions last for the pre-set time (in seconds), the output power of the servo is reduced to the corresponding pre-set level (% of the max. power). 
  • Default: Restores the factory default setting of the connected servo. 

Wide input voltage range 4.8-7.4 V (nominal); operating voltage range 4.8-8.4 V.

25T/5.92 mm output shaft.

Specifications:
Servo dimensionsLow Profile
Servo typeDigital
ProgrammableYes
Thrust at 4.8V [kg/cm]14
Thrust at 6.0V [kg/cm]17
Thrust at 7.4V [kg/cm]19.5
Thrust at 8.4V [kg/cm]20
Speed at 4.8V [s/60st.]0.105
Speed at 6.0V [s/60st.]0.09
Speed at 7.4V [s/60st.]0.08
Speed at 8.4V [s/60st.]0.07
Servo gearsMetal
Ball bearings
High-voltageYes
Power supply [V]4.8 - 8.4
Length [mm]40.8
Width [mm]20.2
Height [mm]26.5
Weight [g]57.2
Intended forOff-road cars
Cable length [mm]100
Loading...