MIBO 1/10 Onroad Low Profile (0.074s/14kg/8.4V) Coreless Servo

Produttore:
MIBO
Categorie:
Codice prodotto:
#MB-2312
Il tuo prezzo:
55,90 €
Disponibilità:
abbastanza disponibile, Invio 3. 4.
Tu ricevi:
Europa4. 4.
MondoStimato 5. 4.

High torque/very high speed digital low-profile servo with steel gear and double BB-ed output shaft. Works great in 1:10 on-road RC cars (suitable for Modified, Stock, FWD, Formula classes). An aluminium middle part of the servo case for perfect cooling under high load.

MB-2312 is programmable using the KAVAN servo USB programmer/interface and PC software.

Programmable Functions:
  • Servo Angle: Maximal servo rotation angle range setting. The default range is ca. 120° within the regular RC signal pulse width range (900~2100µs); ca. 180° within the max. signal pulse width range (500~2500 µs).
  • Servo Neutral: Servo neutral (centre) position setting. 
  • Damping Factor: Servo damping setting – adjust the characteristics of the servo when stopping. 
  • PWM Power: Adjusts the servo output power. The higher the power, the higher the speed and torque of the servo – indeed also the current consumption will be higher. 
  • Sensitivity: Servo sensitivity (Dead Band) setting. The higher sensitivity the narrower the dead band – servo moves only if the change of the signal pulse width is bigger than the dead bandwidth. Too high setting may cause servo jitter in some applications. Range: Ultra High (ca. 1 µs dead band) – High (ca. 2 µs) – Medium (ca. 3 µs) – Low (ca. 4 µs) 
  • Soft Start: Turns on/off the soft start feature. If ON, the servo goes slowly to the initial position corresponding to the servo signal once the power is switched on. 
  • Reverse: Reverses the servo movement direction. 
  • Narrow Band: FUTABA SR Mode – only for use with FUTABA radio channels working in the SR mode. Do not turn the option on if you are using a different setting of your FUTABA radio or any other radio. 
  • SANWA SSR: SANWA SSR Mode - only for use with SANWA radio channels working in the SSR mode. Do not turn the option on if you are using a different setting of your SANWA radio or any other radio. 
  • Lost PPM Protection (Fail-Safe): In the case the control signal from the receiver is lost completely or cannot be decoded correctly (due to interference) the servo can use choose one of three fail-safe modes: 
    • (a) Release: No fail-safe protection. 
    • (b) Keep Position: Keeps the position corresponding to the last correct control signal. 
    • (c) Go Neutral Position: The servo returns to the neutral (1500µs pulse width) position. 
  • Over Load protection: Enables or disables overload protection of the servo in three levels – once the overload conditions last for the pre-set time (in seconds), the output power of the servo is reduced to the corresponding pre-set level (% of the max. power). 
  • Default: Restores the factory default setting of the connected servo. 

Wide input voltage range 4.8–7.4 V (nominal); operating voltage range 4.8–8.4 V.

25T/5.92mm output shaft.

Specifications:
Servo dimensionsLow Profile
Servo typeDigital
ProgrammableYes
Thrust at 4.8V [kg/cm]10
Thrust at 6.0V [kg/cm]12
Thrust at 7.4V [kg/cm]13
Thrust at 8.4V [kg/cm]14
Speed at 4.8V [s/60st.]0.105
Speed at 6.0V [s/60st.]0.093
Speed at 7.4V [s/60st.]0.0828
Speed at 8.4V [s/60st.]0.074
Servo gearsMetal
Ball bearings
High-voltageYes
Power supply [V]4.8 - 8.4
Length [mm]40
Width [mm]20.2
Height [mm]26.1
Weight [g]48
Intended forOn-road cars
Cable length [mm]50
Loading...